Thanksgiving sale ends on 12/1/2024!
The PCO204 is a standard 30A turn-key control panel for the powder coating oven with light and fan control. With a built-in timer function, the included PID controller is able to hold the temperature for a certain period of time then power off the burner. To reset the timer and start another batch, press the blue reset button momentarily. During the batch, one can use a manual switch to turn ON/OFF the burner if needed. A yellow 2-in-1 voltmeter & ammeter shows the system power status. The alarm buzzer can be used for temperature alarm and/or finishing alarm. Separate alarm mute switch is included.
If you do not need light & fan control, please go to
PCO104.
:
- Powder coated wall-mount enclosure with knockouts.
- Dual-line display PID controller with a built-in timer function.
- Illuminated 22mm switches for intuitive operation.
- Flashing buzzer and illuminated alarm mute switch.
- Mini 2-in-1 Volt and Amp meter for displaying system power level.
- Solid State Relay for precise temperature control.
- Contactor for completely power cut off to the element.
- Oven temperature probe w/ mounting screws (both sensor and cable are rated for 900ºF).
- 1/2 inch EMT connector for output connection.
- Strain Relief Power Cord Connector for hard-wiring the power line.
- Side-mount breaker switch for overcurrent protection.
- US seller & US support team. This control panel is designed and manufactured by Auber Instruments. Copyright © Auber Instruments.
Description:
This control panel is built with some of the most popular components Auber Instruments has to offer to the powder coating oven DIY community. With the PID controller SWA-2451B, the oven can quickly heat up to a set temperature and maintain at that temperature for a preset period to cure the parts. When the batch is finished, the coating process can be re-started again by pressing the reset button.
The PID controller can also be used as a thermometer if the operator turns off the heater switch. Then the heater outlet will be powered off completely by the main contactor. Meanwhile, the system performance is enhanced by the SSR (Solid State Relay). When the heater switch is turned to ON position, the PID controller will provide power to the element via SSR, which will take action in only 2 seconds.
The sensor provided in this control panel is our TC-K3MM. It is suitable for low oven application and can handle up to 900 degree F. The 1/8" diameter probe offers a good balance between the fast response time in the air and reasonable mechanical strength. The base of the probe is made of a 0.55" (15 mm) long 5/16"-24 screw for easy mounting. The probe is 4" long and 1/8” (3.0 mm) diameter made of stainless steel with a plated brass base. Default sensor cable length is 6 ft (2m), optional longer cable length 11 ft (3.5m) is also available.
Specifications
| Heater Control Output |
30A, 240VAC maximum. 1/2 inch EMT Connector. |
| Light/Fan Control Output |
5A, 120VAC maximum. 1/2 inch EMT Connector. |
| Input Connection |
30A, four conductors. |
| Sensor |
K Type Thermocouple sensor w/ 4 inch probe. |
| Circuit Breaker |
2P 32A. |
| Temperature Controller |
SWA-2451A. |
| Dimension (W x H x D) |
10 x 8 x 6 inch (25 x 20 x 15 cm) . |
| Weight |
11 lb (5 kg). |
| Warranty |
One (1) year limited warranty. See here for details |
Note:
- The control panel is designed for North America 240V AC power lines which require four line power connections (L1, L2, Neutral and Ground). Please verify your power supply before purchase.
- This control system is designed for heating elements (resistive load) only, not for gas burners or propane heaters. If you want to use the system for a gas burner or other types of heater, please contact us before purchase; otherwise, your purchase may not be covered by our warranty.
- The input power cord (SOOW 10/4) is not included because each user may have different hook up requirements.
- The heating element is not included.
- For a KIT kit version of this panel, please check here.
- This PCO204 is a main control panel, which can operate by itself. If you plan to use this control panel for a larger oven which is over its limit, you may consider using an auxiliary control panel together with this main panel (2-panel setup). See CP30-PCO, CP50-PCO and CP75-PCO for details. It is not recommended to use two main control panels (like 2 x PCO204) for a same oven due to the potential tuning issues.
- Lead time is approx. 2-3 business days.
- Protection plan for this kit is available here.
Front View
Right View of B252020P
Bottom View
Tutorial Video for SWA-2451.
This product was added to our catalog on Thursday 03 May, 2018.
